first commit
This commit is contained in:
commit
8c39952965
1956 changed files with 1460685 additions and 0 deletions
|
|
@ -0,0 +1,260 @@
|
|||
|
||||
/*
|
||||
*******************************************************************************
|
||||
* Copyright (c) 2019, STMicroelectronics
|
||||
* All rights reserved.
|
||||
*
|
||||
* This software component is licensed by ST under BSD 3-Clause license,
|
||||
* the "License"; You may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at:
|
||||
* opensource.org/licenses/BSD-3-Clause
|
||||
*
|
||||
*******************************************************************************
|
||||
* Automatically generated from STM32F401V(D-E)Tx.xml
|
||||
*/
|
||||
#include "Arduino.h"
|
||||
#include "PeripheralPins.h"
|
||||
|
||||
/* =====
|
||||
* Note: Commented lines are alternative possibilities which are not used per default.
|
||||
* If you change them, you will have to know what you do
|
||||
* =====
|
||||
*/
|
||||
|
||||
//*** ADC ***
|
||||
|
||||
#ifdef HAL_ADC_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_ADC[] = {
|
||||
{PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
|
||||
{PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
|
||||
{PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
|
||||
{PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
|
||||
//{PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
|
||||
//{PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
|
||||
//{PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
|
||||
//{PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
|
||||
//{PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
|
||||
//{PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
|
||||
//{PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
|
||||
//{PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
|
||||
{PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
|
||||
{PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
|
||||
//{PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
|
||||
//{PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** No DAC ***
|
||||
|
||||
//*** I2C ***
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_I2C_SDA[] = {
|
||||
//{PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C2)},
|
||||
//{PB_4, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)},
|
||||
{PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
//{PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
//{PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_I2C_SCL[] = {
|
||||
//{PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
||||
{PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
//{PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
//{PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** PWM ***
|
||||
|
||||
#ifdef HAL_TIM_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_PWM[] = {
|
||||
//{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
//{PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
|
||||
//{PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
||||
//{PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
|
||||
//{PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
|
||||
//{PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3
|
||||
//{PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
|
||||
//{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
|
||||
//{PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4
|
||||
//{PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
|
||||
//{PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
//{PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
//{PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
||||
//{PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
||||
//{PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
||||
//{PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
|
||||
//{PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
|
||||
//{PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
|
||||
//{PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
//{PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
||||
{PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
|
||||
//{PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
{PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
|
||||
//{PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
||||
//{PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
//{PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
||||
//{PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
|
||||
//{PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
|
||||
//{PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
|
||||
//{PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
|
||||
//{PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
|
||||
//{PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
|
||||
{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
|
||||
//{PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
||||
//{PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
||||
//{PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
{PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
{PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
||||
//{PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
|
||||
//{PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
|
||||
{PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
|
||||
{PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
|
||||
{PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
|
||||
{PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
|
||||
{PE_5, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
|
||||
//{PE_6, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
|
||||
//{PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
||||
//{PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
||||
//{PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
||||
//{PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
|
||||
//{PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
//{PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
|
||||
{PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** SERIAL ***
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_UART_TX[] = {
|
||||
//{PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
//{PA_11, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
//{PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
//{PC_6, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
{PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_UART_RX[] = {
|
||||
//{PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
//{PA_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
//{PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
//{PC_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
{PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_UART_RTS[] = {
|
||||
//{PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
//{PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
{PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_UART_CTS[] = {
|
||||
//{PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
//{PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
{PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** SPI ***
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SPI_MOSI[] = {
|
||||
{PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
{PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
//{PD_6, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PE_6, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
//{PE_14, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_SPI_MISO[] = {
|
||||
{PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
{PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
//{PE_5, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
//{PE_13, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_SPI_SCLK[] = {
|
||||
{PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
//{PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
{PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
//{PD_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PE_2, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
//{PE_12, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
|
||||
WEAK const PinMap PinMap_SPI_SSEL[] = {
|
||||
{PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
//{PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
//{PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
//{PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
{PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
//{PE_4, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
//{PE_11, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** No CAN ***
|
||||
|
||||
//*** No ETHERNET ***
|
||||
|
||||
//*** No QUADSPI ***
|
||||
|
||||
//*** USB ***
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_USB_OTG_FS[] = {
|
||||
//{PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF
|
||||
//{PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS
|
||||
//{PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID
|
||||
{PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM
|
||||
{PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** No USB_OTG_HS ***
|
||||
//*** SD ***
|
||||
|
||||
#ifdef HAL_SD_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SD[] = {
|
||||
//{PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D4
|
||||
//{PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D5
|
||||
//{PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D6
|
||||
//{PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D7
|
||||
{PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D0
|
||||
{PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1
|
||||
{PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2
|
||||
{PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D3
|
||||
{PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK
|
||||
{PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CMD
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
|
@ -0,0 +1,33 @@
|
|||
/* SYS_WKUP */
|
||||
#ifdef PWR_WAKEUP_PIN1
|
||||
SYS_WKUP1 = PA_0,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN2
|
||||
SYS_WKUP2 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN3
|
||||
SYS_WKUP3 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN4
|
||||
SYS_WKUP4 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN5
|
||||
SYS_WKUP5 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN6
|
||||
SYS_WKUP6 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN7
|
||||
SYS_WKUP7 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN8
|
||||
SYS_WKUP8 = NC,
|
||||
#endif
|
||||
/* USB */
|
||||
#ifdef USBCON
|
||||
USB_OTG_FS_SOF = PA_8,
|
||||
USB_OTG_FS_VBUS = PA_9,
|
||||
USB_OTG_FS_ID = PA_10,
|
||||
USB_OTG_FS_DM = PA_11,
|
||||
USB_OTG_FS_DP = PA_12,
|
||||
#endif
|
||||
|
|
@ -0,0 +1,495 @@
|
|||
/**
|
||||
******************************************************************************
|
||||
* @file stm32f4xx_hal_conf.h
|
||||
* @brief HAL configuration file.
|
||||
******************************************************************************
|
||||
* @attention
|
||||
*
|
||||
* <h2><center>© Copyright (c) 2017 STMicroelectronics.
|
||||
* All rights reserved.</center></h2>
|
||||
*
|
||||
* This software component is licensed by ST under BSD 3-Clause license,
|
||||
* the "License"; You may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at:
|
||||
* opensource.org/licenses/BSD-3-Clause
|
||||
*
|
||||
******************************************************************************
|
||||
*/
|
||||
|
||||
/* Define to prevent recursive inclusion -------------------------------------*/
|
||||
#ifndef __STM32F4xx_HAL_CONF_CUSTOM
|
||||
#define __STM32F4xx_HAL_CONF_CUSTOM
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
/* Exported types ------------------------------------------------------------*/
|
||||
/* Exported constants --------------------------------------------------------*/
|
||||
|
||||
/* ########################## Module Selection ############################## */
|
||||
/**
|
||||
* @brief This is the list of modules to be used in the HAL driver
|
||||
*/
|
||||
#define HAL_MODULE_ENABLED
|
||||
#define HAL_ADC_MODULE_ENABLED
|
||||
#define HAL_CRC_MODULE_ENABLED
|
||||
#define HAL_DMA_MODULE_ENABLED
|
||||
#define HAL_FLASH_MODULE_ENABLED
|
||||
#define HAL_GPIO_MODULE_ENABLED
|
||||
#define HAL_I2C_MODULE_ENABLED
|
||||
#define HAL_IWDG_MODULE_ENABLED
|
||||
#define HAL_PWR_MODULE_ENABLED
|
||||
#define HAL_RCC_MODULE_ENABLED
|
||||
#define HAL_RTC_MODULE_ENABLED
|
||||
#define HAL_SD_MODULE_ENABLED
|
||||
#define HAL_SPI_MODULE_ENABLED
|
||||
#define HAL_TIM_MODULE_ENABLED
|
||||
#define HAL_CORTEX_MODULE_ENABLED
|
||||
//#define HAL_PCD_MODULE_ENABLED // Automatically added if any type of USB is enabled, as in Arduino IDE. (STM32 v3.10700.191028)
|
||||
|
||||
//#define HAL_CAN_MODULE_ENABLED
|
||||
//#define HAL_CAN_LEGACY_MODULE_ENABLED
|
||||
//#define HAL_CEC_MODULE_ENABLED
|
||||
//#define HAL_CRYP_MODULE_ENABLED
|
||||
//#define HAL_DAC_MODULE_ENABLED
|
||||
//#define HAL_DCMI_MODULE_ENABLED
|
||||
//#define HAL_DMA2D_MODULE_ENABLED
|
||||
//#define HAL_ETH_MODULE_ENABLED
|
||||
//#define HAL_NAND_MODULE_ENABLED
|
||||
//#define HAL_NOR_MODULE_ENABLED
|
||||
//#define HAL_PCCARD_MODULE_ENABLED
|
||||
//#define HAL_SRAM_MODULE_ENABLED
|
||||
//#define HAL_SDRAM_MODULE_ENABLED
|
||||
//#define HAL_HASH_MODULE_ENABLED
|
||||
//#define HAL_EXTI_MODULE_ENABLED
|
||||
//#define HAL_SMBUS_MODULE_ENABLED
|
||||
//#define HAL_I2S_MODULE_ENABLED
|
||||
//#define HAL_LTDC_MODULE_ENABLED
|
||||
//#define HAL_DSI_MODULE_ENABLED
|
||||
//#define HAL_QSPI_MODULE_ENABLED
|
||||
//#define HAL_RNG_MODULE_ENABLED
|
||||
//#define HAL_SAI_MODULE_ENABLED
|
||||
//#define HAL_UART_MODULE_ENABLED // by default
|
||||
//#define HAL_USART_MODULE_ENABLED
|
||||
//#define HAL_IRDA_MODULE_ENABLED
|
||||
//#define HAL_SMARTCARD_MODULE_ENABLED
|
||||
//#define HAL_WWDG_MODULE_ENABLED
|
||||
//#define HAL_HCD_MODULE_ENABLED
|
||||
//#define HAL_FMPI2C_MODULE_ENABLED
|
||||
//#define HAL_SPDIFRX_MODULE_ENABLED
|
||||
//#define HAL_DFSDM_MODULE_ENABLED
|
||||
//#define HAL_LPTIM_MODULE_ENABLED
|
||||
//#define HAL_MMC_MODULE_ENABLED
|
||||
|
||||
/* ########################## HSE/HSI Values adaptation ##################### */
|
||||
/**
|
||||
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSE is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#ifndef HSE_VALUE
|
||||
#define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
|
||||
#endif /* HSE_VALUE */
|
||||
|
||||
#ifndef HSE_STARTUP_TIMEOUT
|
||||
#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
|
||||
#endif /* HSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief Internal High Speed oscillator (HSI) value.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSI is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#ifndef HSI_VALUE
|
||||
#define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */
|
||||
#endif /* HSI_VALUE */
|
||||
|
||||
/**
|
||||
* @brief Internal Low Speed oscillator (LSI) value.
|
||||
*/
|
||||
#ifndef LSI_VALUE
|
||||
#define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */
|
||||
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
|
||||
The real value may vary depending on the variations
|
||||
in voltage and temperature. */
|
||||
/**
|
||||
* @brief External Low Speed oscillator (LSE) value.
|
||||
*/
|
||||
#ifndef LSE_VALUE
|
||||
#define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
|
||||
#endif /* LSE_VALUE */
|
||||
|
||||
#ifndef LSE_STARTUP_TIMEOUT
|
||||
#define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
|
||||
#endif /* LSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief External clock source for I2S peripheral
|
||||
* This value is used by the I2S HAL module to compute the I2S clock source
|
||||
* frequency, this source is inserted directly through I2S_CKIN pad.
|
||||
*/
|
||||
#ifndef EXTERNAL_CLOCK_VALUE
|
||||
#define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/
|
||||
#endif /* EXTERNAL_CLOCK_VALUE */
|
||||
|
||||
/* Tip: To avoid modifying this file each time you need to use different HSE,
|
||||
=== you can define the HSE value in your toolchain compiler preprocessor. */
|
||||
|
||||
/* ########################### System Configuration ######################### */
|
||||
/**
|
||||
* @brief This is the HAL system configuration section
|
||||
*/
|
||||
#if !defined (VDD_VALUE)
|
||||
#define VDD_VALUE 3300U /*!< Value of VDD in mv */
|
||||
#endif
|
||||
#if !defined (TICK_INT_PRIORITY)
|
||||
#define TICK_INT_PRIORITY 0x00U /*!< tick interrupt priority */
|
||||
#endif
|
||||
#if !defined (USE_RTOS)
|
||||
#define USE_RTOS 0U
|
||||
#endif
|
||||
#if !defined (PREFETCH_ENABLE)
|
||||
#define PREFETCH_ENABLE 1U
|
||||
#endif
|
||||
#if !defined (INSTRUCTION_CACHE_ENABLE)
|
||||
#define INSTRUCTION_CACHE_ENABLE 1U
|
||||
#endif
|
||||
#if !defined (DATA_CACHE_ENABLE)
|
||||
#define DATA_CACHE_ENABLE 1U
|
||||
#endif
|
||||
|
||||
#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
|
||||
#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
|
||||
#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
|
||||
#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
|
||||
#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
|
||||
#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
|
||||
#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
|
||||
#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
|
||||
#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
|
||||
#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
|
||||
#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
|
||||
#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
|
||||
#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
|
||||
#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */
|
||||
#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
|
||||
#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
|
||||
#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
|
||||
#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
|
||||
#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
|
||||
#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
|
||||
#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
|
||||
#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
|
||||
#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
|
||||
#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
|
||||
#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
|
||||
#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
|
||||
#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
|
||||
#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
|
||||
#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
|
||||
#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
|
||||
#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
|
||||
#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
|
||||
#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
|
||||
#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
|
||||
#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
|
||||
#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
|
||||
#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
|
||||
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
|
||||
|
||||
/* ########################## Assert Selection ############################## */
|
||||
/**
|
||||
* @brief Uncomment the line below to expanse the "assert_param" macro in the
|
||||
* HAL drivers code
|
||||
*/
|
||||
/* #define USE_FULL_ASSERT 1U */
|
||||
|
||||
/* ################## Ethernet peripheral configuration ##################### */
|
||||
|
||||
/* Section 1 : Ethernet peripheral configuration */
|
||||
|
||||
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
|
||||
#define MAC_ADDR0 2U
|
||||
#define MAC_ADDR1 0U
|
||||
#define MAC_ADDR2 0U
|
||||
#define MAC_ADDR3 0U
|
||||
#define MAC_ADDR4 0U
|
||||
#define MAC_ADDR5 0U
|
||||
|
||||
/* Definition of the Ethernet driver buffers size and count */
|
||||
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
|
||||
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
|
||||
#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
|
||||
#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
|
||||
|
||||
/* Section 2: PHY configuration section */
|
||||
|
||||
/* DP83848_PHY_ADDRESS Address*/
|
||||
#define DP83848_PHY_ADDRESS 0x01U
|
||||
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
|
||||
#define PHY_RESET_DELAY 0x000000FFU
|
||||
/* PHY Configuration delay */
|
||||
#define PHY_CONFIG_DELAY 0x00000FFFU
|
||||
|
||||
#define PHY_READ_TO 0x0000FFFFU
|
||||
#define PHY_WRITE_TO 0x0000FFFFU
|
||||
|
||||
/* Section 3: Common PHY Registers */
|
||||
|
||||
#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
|
||||
#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
|
||||
|
||||
#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
|
||||
#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
|
||||
#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
|
||||
#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
|
||||
#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
|
||||
#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
|
||||
#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
|
||||
#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
|
||||
#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
|
||||
#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
|
||||
|
||||
#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
|
||||
#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
|
||||
#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
|
||||
|
||||
/* Section 4: Extended PHY Registers */
|
||||
#define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */
|
||||
|
||||
#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */
|
||||
#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */
|
||||
|
||||
/* ################## SPI peripheral configuration ########################## */
|
||||
|
||||
/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
|
||||
* Activated: CRC code is present inside driver
|
||||
* Deactivated: CRC code cleaned from driver
|
||||
*/
|
||||
#ifndef USE_SPI_CRC
|
||||
#define USE_SPI_CRC 0U
|
||||
#endif
|
||||
|
||||
/* Includes ------------------------------------------------------------------*/
|
||||
/**
|
||||
* @brief Include module's header file
|
||||
*/
|
||||
|
||||
#ifdef HAL_RCC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_rcc.h"
|
||||
#endif /* HAL_RCC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_GPIO_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_gpio.h"
|
||||
#endif /* HAL_GPIO_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_EXTI_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_exti.h"
|
||||
#endif /* HAL_EXTI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DMA_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_dma.h"
|
||||
#endif /* HAL_DMA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CORTEX_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_cortex.h"
|
||||
#endif /* HAL_CORTEX_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ADC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_adc.h"
|
||||
#endif /* HAL_ADC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CAN_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_can.h"
|
||||
#endif /* HAL_CAN_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_can_legacy.h"
|
||||
#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_crc.h"
|
||||
#endif /* HAL_CRC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRYP_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_cryp.h"
|
||||
#endif /* HAL_CRYP_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DMA2D_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_dma2d.h"
|
||||
#endif /* HAL_DMA2D_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DAC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_dac.h"
|
||||
#endif /* HAL_DAC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DCMI_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_dcmi.h"
|
||||
#endif /* HAL_DCMI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ETH_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_eth.h"
|
||||
#endif /* HAL_ETH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_FLASH_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_flash.h"
|
||||
#endif /* HAL_FLASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SRAM_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_sram.h"
|
||||
#endif /* HAL_SRAM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NOR_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_nor.h"
|
||||
#endif /* HAL_NOR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NAND_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_nand.h"
|
||||
#endif /* HAL_NAND_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PCCARD_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_pccard.h"
|
||||
#endif /* HAL_PCCARD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SDRAM_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_sdram.h"
|
||||
#endif /* HAL_SDRAM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HASH_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_hash.h"
|
||||
#endif /* HAL_HASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_i2c.h"
|
||||
#endif /* HAL_I2C_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SMBUS_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_smbus.h"
|
||||
#endif /* HAL_SMBUS_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2S_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_i2s.h"
|
||||
#endif /* HAL_I2S_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IWDG_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_iwdg.h"
|
||||
#endif /* HAL_IWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_LTDC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_ltdc.h"
|
||||
#endif /* HAL_LTDC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PWR_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_pwr.h"
|
||||
#endif /* HAL_PWR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RNG_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_rng.h"
|
||||
#endif /* HAL_RNG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RTC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_rtc.h"
|
||||
#endif /* HAL_RTC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SAI_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_sai.h"
|
||||
#endif /* HAL_SAI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SD_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_sd.h"
|
||||
#endif /* HAL_SD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_spi.h"
|
||||
#endif /* HAL_SPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_TIM_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_tim.h"
|
||||
#endif /* HAL_TIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_uart.h"
|
||||
#endif /* HAL_UART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_USART_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_usart.h"
|
||||
#endif /* HAL_USART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IRDA_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_irda.h"
|
||||
#endif /* HAL_IRDA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SMARTCARD_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_smartcard.h"
|
||||
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_WWDG_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_wwdg.h"
|
||||
#endif /* HAL_WWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_pcd.h"
|
||||
#endif /* HAL_PCD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HCD_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_hcd.h"
|
||||
#endif /* HAL_HCD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DSI_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_dsi.h"
|
||||
#endif /* HAL_DSI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_qspi.h"
|
||||
#endif /* HAL_QSPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CEC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_cec.h"
|
||||
#endif /* HAL_CEC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_FMPI2C_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_fmpi2c.h"
|
||||
#endif /* HAL_FMPI2C_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SPDIFRX_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_spdifrx.h"
|
||||
#endif /* HAL_SPDIFRX_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DFSDM_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_dfsdm.h"
|
||||
#endif /* HAL_DFSDM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_LPTIM_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_lptim.h"
|
||||
#endif /* HAL_LPTIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_MMC_MODULE_ENABLED
|
||||
#include "stm32f4xx_hal_mmc.h"
|
||||
#endif /* HAL_MMC_MODULE_ENABLED */
|
||||
|
||||
/* Exported macro ------------------------------------------------------------*/
|
||||
#ifdef USE_FULL_ASSERT
|
||||
/**
|
||||
* @brief The assert_param macro is used for function's parameters check.
|
||||
* @param expr If expr is false, it calls assert_failed function
|
||||
* which reports the name of the source file and the source
|
||||
* line number of the call that failed.
|
||||
* If expr is true, it returns no value.
|
||||
* @retval None
|
||||
*/
|
||||
#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
|
||||
/* Exported functions ------------------------------------------------------- */
|
||||
void assert_failed(uint8_t *file, uint32_t line);
|
||||
#else
|
||||
#define assert_param(expr) ((void)0U)
|
||||
#endif /* USE_FULL_ASSERT */
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __STM32F4xx_HAL_CONF_CUSTOM_H */
|
||||
|
||||
|
||||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
||||
|
|
@ -0,0 +1,187 @@
|
|||
/*
|
||||
*****************************************************************************
|
||||
**
|
||||
** File : ldscript.ld
|
||||
**
|
||||
** Abstract : Linker script for STM32F401RETx Device with
|
||||
** 512KByte FLASH, 96KByte RAM
|
||||
**
|
||||
** Set heap size, stack size and stack location according
|
||||
** to application requirements.
|
||||
**
|
||||
** Set memory bank area and size if external memory is used.
|
||||
**
|
||||
** Target : STMicroelectronics STM32
|
||||
**
|
||||
**
|
||||
** Distribution: The file is distributed as is, without any warranty
|
||||
** of any kind.
|
||||
**
|
||||
*****************************************************************************
|
||||
** @attention
|
||||
**
|
||||
** <h2><center>© COPYRIGHT(c) 2014 Ac6</center></h2>
|
||||
**
|
||||
** Redistribution and use in source and binary forms, with or without modification,
|
||||
** are permitted provided that the following conditions are met:
|
||||
** 1. Redistributions of source code must retain the above copyright notice,
|
||||
** this list of conditions and the following disclaimer.
|
||||
** 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
** this list of conditions and the following disclaimer in the documentation
|
||||
** and/or other materials provided with the distribution.
|
||||
** 3. Neither the name of Ac6 nor the names of its contributors
|
||||
** may be used to endorse or promote products derived from this software
|
||||
** without specific prior written permission.
|
||||
**
|
||||
** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
||||
** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
||||
** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
||||
** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
||||
** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
||||
** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
**
|
||||
*****************************************************************************
|
||||
*/
|
||||
|
||||
/* Entry Point */
|
||||
ENTRY(Reset_Handler)
|
||||
|
||||
/* Highest address of the user mode stack */
|
||||
_estack = 0x20018000; /* end of RAM */
|
||||
/* Generate a link error if heap and stack don't fit into RAM */
|
||||
_Min_Heap_Size = 0x200; /* required amount of heap */
|
||||
_Min_Stack_Size = 0x400; /* required amount of stack */
|
||||
|
||||
/* Specify the memory areas */
|
||||
MEMORY
|
||||
{
|
||||
FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 512K
|
||||
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 96K
|
||||
}
|
||||
|
||||
/* Define output sections */
|
||||
SECTIONS
|
||||
{
|
||||
/* The startup code goes first into FLASH */
|
||||
.isr_vector :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
KEEP(*(.isr_vector)) /* Startup code */
|
||||
. = ALIGN(4);
|
||||
} >FLASH
|
||||
|
||||
/* The program code and other data goes into FLASH */
|
||||
.text :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
*(.text) /* .text sections (code) */
|
||||
*(.text*) /* .text* sections (code) */
|
||||
*(.glue_7) /* glue arm to thumb code */
|
||||
*(.glue_7t) /* glue thumb to arm code */
|
||||
*(.eh_frame)
|
||||
|
||||
KEEP (*(.init))
|
||||
KEEP (*(.fini))
|
||||
|
||||
. = ALIGN(4);
|
||||
_etext = .; /* define a global symbols at end of code */
|
||||
} >FLASH
|
||||
|
||||
/* Constant data goes into FLASH */
|
||||
.rodata :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
*(.rodata) /* .rodata sections (constants, strings, etc.) */
|
||||
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
|
||||
. = ALIGN(4);
|
||||
} >FLASH
|
||||
|
||||
.ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
|
||||
.ARM : {
|
||||
__exidx_start = .;
|
||||
*(.ARM.exidx*)
|
||||
__exidx_end = .;
|
||||
} >FLASH
|
||||
|
||||
.preinit_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__preinit_array_start = .);
|
||||
KEEP (*(.preinit_array*))
|
||||
PROVIDE_HIDDEN (__preinit_array_end = .);
|
||||
} >FLASH
|
||||
.init_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__init_array_start = .);
|
||||
KEEP (*(SORT(.init_array.*)))
|
||||
KEEP (*(.init_array*))
|
||||
PROVIDE_HIDDEN (__init_array_end = .);
|
||||
} >FLASH
|
||||
.fini_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__fini_array_start = .);
|
||||
KEEP (*(SORT(.fini_array.*)))
|
||||
KEEP (*(.fini_array*))
|
||||
PROVIDE_HIDDEN (__fini_array_end = .);
|
||||
} >FLASH
|
||||
|
||||
/* used by the startup to initialize data */
|
||||
_sidata = LOADADDR(.data);
|
||||
|
||||
/* Initialized data sections goes into RAM, load LMA copy after code */
|
||||
.data :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
_sdata = .; /* create a global symbol at data start */
|
||||
*(.data) /* .data sections */
|
||||
*(.data*) /* .data* sections */
|
||||
|
||||
. = ALIGN(4);
|
||||
_edata = .; /* define a global symbol at data end */
|
||||
} >RAM AT> FLASH
|
||||
|
||||
|
||||
/* Uninitialized data section */
|
||||
. = ALIGN(4);
|
||||
.bss :
|
||||
{
|
||||
/* This is used by the startup in order to initialize the .bss secion */
|
||||
_sbss = .; /* define a global symbol at bss start */
|
||||
__bss_start__ = _sbss;
|
||||
*(.bss)
|
||||
*(.bss*)
|
||||
*(COMMON)
|
||||
|
||||
. = ALIGN(4);
|
||||
_ebss = .; /* define a global symbol at bss end */
|
||||
__bss_end__ = _ebss;
|
||||
} >RAM
|
||||
|
||||
/* User_heap_stack section, used to check that there is enough RAM left */
|
||||
._user_heap_stack :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
PROVIDE ( end = . );
|
||||
PROVIDE ( _end = . );
|
||||
. = . + _Min_Heap_Size;
|
||||
. = . + _Min_Stack_Size;
|
||||
. = ALIGN(4);
|
||||
} >RAM
|
||||
|
||||
|
||||
|
||||
/* Remove information from the standard libraries */
|
||||
/DISCARD/ :
|
||||
{
|
||||
libc.a ( * )
|
||||
libm.a ( * )
|
||||
libgcc.a ( * )
|
||||
}
|
||||
|
||||
.ARM.attributes 0 : { *(.ARM.attributes) }
|
||||
}
|
||||
|
||||
|
||||
|
|
@ -0,0 +1,310 @@
|
|||
/*
|
||||
*******************************************************************************
|
||||
* Copyright (c) 2017, STMicroelectronics
|
||||
* All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright notice,
|
||||
* this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
* this list of conditions and the following disclaimer in the documentation
|
||||
* and/or other materials provided with the distribution.
|
||||
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
||||
* may be used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
||||
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
||||
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
||||
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
||||
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
||||
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
*******************************************************************************
|
||||
*/
|
||||
|
||||
#include "pins_arduino.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
#ifdef ARDUINO_STEVAL
|
||||
// Pin number
|
||||
// This array allows to wrap Arduino pin number(Dx or x)
|
||||
// to STM32 PinName (PX_n)
|
||||
const PinName digitalPin[] = {
|
||||
PA_9, // TX
|
||||
PA_10, // RX
|
||||
|
||||
// WIFI
|
||||
PD_3, // CTS
|
||||
PD_4, // RTS
|
||||
PD_5, // TX
|
||||
PD_6, // RX
|
||||
PB_5, // WIFI_WAKEUP
|
||||
PE_11, // WIFI_RESET
|
||||
PE_12, // WIFI_BOOT
|
||||
|
||||
// STATUS_LED
|
||||
PE_1, //STATUS_LED
|
||||
|
||||
// SPI USER
|
||||
PB_12, // SPI_CS
|
||||
PB_15, // SPI_MOSI
|
||||
PB_14, // SPI_MISO
|
||||
PB_13, // SPI_SCK
|
||||
|
||||
// I2C USER
|
||||
PB_7, // SDA
|
||||
PB_6, // SCL
|
||||
|
||||
// SPI
|
||||
PA_4, // SPI_CS
|
||||
PA_5, // SPI_SCK
|
||||
PA_6, // SPI_MISO
|
||||
PA_7, // SPI_MOSI
|
||||
|
||||
// JTAG
|
||||
PA_13, // JTAG_TMS/SWDIO
|
||||
PA_14, // JTAG_TCK/SWCLK
|
||||
PB_3, // JTAG_TDO/SWO
|
||||
|
||||
// SDCARD
|
||||
PC_8, // SDIO_D0
|
||||
PC_9, // SDIO_D1
|
||||
PA_15, // SD_CARD_DETECT
|
||||
PC_10, // SDIO_D2
|
||||
PC_11, // SDIO_D3
|
||||
PC_12, // SDIO_CK
|
||||
PD_2, // SDIO_CMD
|
||||
|
||||
// OTG
|
||||
PA_11, // OTG_DM
|
||||
PA_12, // OTG_DP
|
||||
|
||||
// IR/PROBE
|
||||
PD_1, // IR_OUT
|
||||
PC_1, // IR_ON
|
||||
|
||||
// USER_PINS
|
||||
PD_7, // USER3
|
||||
PB_9, // USER1
|
||||
PE_0, // USER2
|
||||
PB_4, // USER4
|
||||
|
||||
// USERKET
|
||||
PE_7, // USER_BUTTON
|
||||
|
||||
// ENDSTOPS
|
||||
PD_8, // X_STOP
|
||||
PD_9, // Y_STOP
|
||||
PD_10, // Z_STOP
|
||||
PD_11, // U_STOP
|
||||
PA_8, // V_STOP
|
||||
PD_0, // W_STOP
|
||||
|
||||
// HEATERS
|
||||
PD_13, // BED_HEAT_2
|
||||
PD_14, // BED_HEAT_1
|
||||
PD_15, // BED_HEAT_3
|
||||
PC_7, // E1_HEAT_PWM
|
||||
PB_0, // E2_HEAT_PWM
|
||||
PB_1, // E3_HEAT_PWM
|
||||
|
||||
// THERMISTOR
|
||||
PC_2, // BED_THERMISTOR_1
|
||||
PC_3, // BED_THERMISTOR_2
|
||||
PA_3, // BED_THERMISTOR_3
|
||||
PA_0, // E1_THERMISTOR
|
||||
PA_1, // E2_THERMISTOR
|
||||
PA_2, // E3_THERMISTOR
|
||||
|
||||
// FANS
|
||||
PC_4, // E1_FAN
|
||||
PC_5, // E2_FAN
|
||||
PE_8, // E3_FAN
|
||||
|
||||
// X_MOTOR
|
||||
PE_13, // X_RESET
|
||||
PE_14, // X_PWM
|
||||
PE_15, // X_DIR
|
||||
|
||||
// Y_MOTOR
|
||||
PE_10, // Y_RESET
|
||||
PB_10, // Y_PWM
|
||||
PE_9, // Y_DIR
|
||||
|
||||
// Z_MOTOR
|
||||
PC_15, // Z_RESET
|
||||
PC_6, // Z_PWM
|
||||
PC_0, // Z_DIR
|
||||
|
||||
// E1_MOTOR
|
||||
PC_14, // E1_RESET
|
||||
PC_13, // E1_DIR
|
||||
PD_12, // E1_PWM
|
||||
|
||||
// E2_MOTOR
|
||||
PE_4, // E2_RESET
|
||||
PE_5, // E2_PWM
|
||||
PE_6, // E2_DIR
|
||||
|
||||
// E3_MOTOR
|
||||
PE_3, // E3_RESET
|
||||
PE_2, // E3_DIR
|
||||
PB_8 // E3_PWM
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
// ----------------------------------------------------------------------------
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
/**
|
||||
* @brief System Clock Configuration
|
||||
* The system Clock is configured as follow :
|
||||
* System Clock source = PLL (HSI)
|
||||
* SYSCLK(Hz) = 84000000
|
||||
* HCLK(Hz) = 84000000
|
||||
* AHB Prescaler = 1
|
||||
* APB1 Prescaler = 2
|
||||
* APB2 Prescaler = 1
|
||||
* HSI Frequency(Hz) = 16000000
|
||||
* PLL_M = 16
|
||||
* PLL_N = 336
|
||||
* PLL_P = 4
|
||||
* PLL_Q = 7
|
||||
* VDD(V) = 3.3
|
||||
* Main regulator output voltage = Scale2 mode
|
||||
* Flash Latency(WS) = 2
|
||||
* @param None
|
||||
* @retval None
|
||||
*/
|
||||
WEAK void SystemClock_Config(void)
|
||||
{
|
||||
RCC_OscInitTypeDef RCC_OscInitStruct = {};
|
||||
RCC_ClkInitTypeDef RCC_ClkInitStruct = {};
|
||||
|
||||
/* Configure the main internal regulator output voltage */
|
||||
__HAL_RCC_PWR_CLK_ENABLE();
|
||||
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
|
||||
|
||||
/* Initializes the CPU, AHB and APB busses clocks */
|
||||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
|
||||
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
|
||||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
||||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
|
||||
RCC_OscInitStruct.PLL.PLLM = 15;
|
||||
RCC_OscInitStruct.PLL.PLLN = 144;
|
||||
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
|
||||
RCC_OscInitStruct.PLL.PLLQ = 5;
|
||||
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
|
||||
Error_Handler();
|
||||
}
|
||||
/* Initializes the CPU, AHB and APB busses clocks */
|
||||
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
|
||||
| RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
|
||||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
|
||||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
||||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
|
||||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
|
||||
|
||||
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) {
|
||||
Error_Handler();
|
||||
}
|
||||
}
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
|
||||
// PA_0 54 // E1_THERMISTOR
|
||||
// PA_1 55 // E2_THERMISTOR
|
||||
// PA_2 56 // E3_THERMISTOR
|
||||
// PA_3 53 // BED_THERMISTOR_3
|
||||
// PA_4 16 // SPI_CS
|
||||
// PA_5 17 // SPI_SCK
|
||||
// PA_6 18 // SPI_MISO
|
||||
// PA_7 19 // SPI_MOSI
|
||||
// PA_8 43 // V_STOP
|
||||
// PA_9 0 //TX
|
||||
// PA_10 1 //RX
|
||||
// PA_11 30 //OTG_DM
|
||||
// PA_12 31 //OTG_DP
|
||||
// PA_13 20 // JTAG_TMS/SWDIO
|
||||
// PA_14 21 // JTAG_TCK/SWCLK
|
||||
// PA_15 25 // SD_CARD_DETECT
|
||||
// PB_0 49 // E2_HEAT_PWM
|
||||
// PB_1 50 // E3_HEAT_PWM
|
||||
// PB_3 22 // JTAG_TDO/SWO
|
||||
// PB_4 37 // USER4
|
||||
// PB_5 6 // WIFI_WAKEUP
|
||||
// PB_6 15 // SCL
|
||||
// PB_7 14 // SDA
|
||||
// PB_8 77 // E3_PWM
|
||||
// PB_9 35 // USER1
|
||||
// PB_10 64 // Y_PWM
|
||||
// PB_12 10 // SPI_CS
|
||||
// PB_13 13 // SPI_SCK
|
||||
// PB_14 12 // SPI_MISO
|
||||
// PB_15 11 // SPI_MOSI
|
||||
// PC_0 68 // Z_DIR
|
||||
// PC_1 33 //IR_ON
|
||||
// PC_2 51 // BED_THERMISTOR_1
|
||||
// PC_3 52 // BED_THERMISTOR_2
|
||||
// PC_4 57 // E1_FAN
|
||||
// PC_5 58 // E2_FAN
|
||||
// PC_6 67 // Z_PWM
|
||||
// PC_7 48 // E1_HEAT_PWM
|
||||
// PC_8 23 // SDIO_D0
|
||||
// PC_9 24 // SDIO_D1
|
||||
// PC_10 26 // SDIO_D2
|
||||
// PC_11 27 // SDIO_D3
|
||||
// PC_12 28 // SDIO_CK
|
||||
// PC_13 70 // E1_DIR
|
||||
// PC_14 69 // E1_RESET
|
||||
// PC_15 66 // Z_RESET
|
||||
// PD_0 44 // W_STOP
|
||||
// PD_1 32 //IR_OUT
|
||||
// PD_2 29 // SDIO_CMD
|
||||
// PD_3 2 // CTS
|
||||
// PD_4 3 // RTS
|
||||
// PD_5 4 // TX
|
||||
// PD_6 5 // RX
|
||||
// PD_7 34 // USER3
|
||||
// PD_8 39 // X_STOP
|
||||
// PD_9 40 // Y_STOP
|
||||
// PD_10 41 // Z_STOP
|
||||
// PD_11 42 // U_STOP
|
||||
// PD_12 71 // E1_PWM
|
||||
// PD_13 45 // BED_HEAT_2
|
||||
// PD_14 46 // BED_HEAT_1
|
||||
// PD_15 47 // BED_HEAT_3
|
||||
// PE_0 36 // USER2
|
||||
// PE_1 9 // STATUS_LED
|
||||
// PE_2 76 // E3_DIR
|
||||
// PE_3 75 // E3_RESET
|
||||
// PE_4 72 // E2_RESET
|
||||
// PE_5 73 // E2_PWM
|
||||
// PE_6 74 // E2_DIR
|
||||
// PE_7 38 // USER_BUTTON
|
||||
// PE_8 59 // E3_FAN
|
||||
// PE_9 65 // Y_DIR
|
||||
// PE_10 63 // Y_RESET
|
||||
// PE_11 7 // WIFI_RESET
|
||||
// PE_12 8 // WIFI_BOOT
|
||||
// PE_13 60 // X_RESET
|
||||
// PE_14 61 // X_PWM
|
||||
// PE_15 62 // X_DIR
|
||||
|
|
@ -0,0 +1,327 @@
|
|||
/*
|
||||
*******************************************************************************
|
||||
* Copyright (c) 2017, STMicroelectronics
|
||||
* All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright notice,
|
||||
* this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
* this list of conditions and the following disclaimer in the documentation
|
||||
* and/or other materials provided with the distribution.
|
||||
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
||||
* may be used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
||||
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
||||
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
||||
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
||||
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
||||
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
*******************************************************************************
|
||||
*/
|
||||
|
||||
#ifndef _VARIANT_ARDUINO_STM32_
|
||||
#define _VARIANT_ARDUINO_STM32_
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Pins
|
||||
*----------------------------------------------------------------------------*/
|
||||
#ifdef ARDUINO_STEVAL
|
||||
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Pins
|
||||
*----------------------------------------------------------------------------*/
|
||||
// USART1_MAIN
|
||||
#define PA9 0 //TX
|
||||
#define PA10 1 //RX
|
||||
|
||||
// WIFI (USART2)
|
||||
#define PD3 2 // CTS
|
||||
#define PD4 3 // RTS
|
||||
#define PD5 4 // TX
|
||||
#define PD6 5 // RX
|
||||
#define PB5 6 // WIFI_WAKEUP
|
||||
#define PE11 7 // WIFI_RESET
|
||||
#define PE12 8 // WIFI_BOOT
|
||||
|
||||
// STATUS_LED
|
||||
#define PE1 9 // STATUS_LED
|
||||
|
||||
// SPI USER
|
||||
#define PB12 10 // SPI_CS
|
||||
#define PB15 11 // SPI_MOSI
|
||||
#define PB14 12 // SPI_MISO
|
||||
#define PB13 13 // SPI_SCK
|
||||
|
||||
// I2C USER
|
||||
#define PB7 14 // SDA
|
||||
#define PB6 15 // SCL
|
||||
|
||||
// SPI
|
||||
#define PA4 16 // SPI_CS
|
||||
#define PA5 17 // SPI_SCK
|
||||
#define PA6 18 // SPI_MISO
|
||||
#define PA7 19 // SPI_MOSI
|
||||
|
||||
// JTAG
|
||||
#define PA13 20 // JTAG_TMS/SWDIO
|
||||
#define PA14 21 // JTAG_TCK/SWCLK
|
||||
#define PB3 22 // JTAG_TDO/SWO
|
||||
|
||||
// SDCARD
|
||||
#define PC8 23 // SDIO_D0
|
||||
#define PC9 24 // SDIO_D1
|
||||
#define PA15 25 // SD_CARD_DETECT
|
||||
#define PC10 26 // SDIO_D2
|
||||
#define PC11 27 // SDIO_D3
|
||||
#define PC12 28 // SDIO_CK
|
||||
#define PD2 29 // SDIO_CMD
|
||||
|
||||
// OTG
|
||||
#define PA11 30 //OTG_DM
|
||||
#define PA12 31 //OTG_DP
|
||||
|
||||
// IR/PROBE
|
||||
#define PD1 32 //IR_OUT
|
||||
#define PC1 33 //IR_ON
|
||||
|
||||
// USER_PINS
|
||||
#define PD7 34 // USER3
|
||||
#define PB9 35 // USER1
|
||||
#define PE0 36 // USER2
|
||||
#define PB4 37 // USER4
|
||||
|
||||
// USERKET
|
||||
#define PE7 38 // USER_BUTTON
|
||||
|
||||
// ENDSTOPS
|
||||
#define PD8 39 // X_STOP
|
||||
#define PD9 40 // Y_STOP
|
||||
#define PD10 41 // Z_STOP
|
||||
#define PD11 42 // U_STOP
|
||||
#define PA8 43 // V_STOP
|
||||
#define PD0 44 // W_STOP
|
||||
|
||||
// HEATERS
|
||||
#define PD13 45 // BED_HEAT_2
|
||||
#define PD14 46 // BED_HEAT_1
|
||||
#define PD15 47 // BED_HEAT_3
|
||||
#define PC7 48 // E1_HEAT_PWM
|
||||
#define PB0 49 // E2_HEAT_PWM
|
||||
#define PB1 50 // E3_HEAT_PWM
|
||||
|
||||
// THERMISTOR
|
||||
#define PC2 51 // BED_THERMISTOR_1
|
||||
#define PC3 52 // BED_THERMISTOR_2
|
||||
#define PA3 53 // BED_THERMISTOR_3
|
||||
#define PA0 54 // E1_THERMISTOR
|
||||
#define PA1 55 // E2_THERMISTOR
|
||||
#define PA2 56 // E3_THERMISTOR
|
||||
|
||||
// FANS
|
||||
#define PC4 57 // E1_FAN
|
||||
#define PC5 58 // E2_FAN
|
||||
#define PE8 59 // E3_FAN
|
||||
|
||||
// X_MOTOR
|
||||
#define PE13 60 // X_RESET
|
||||
#define PE14 61 // X_PWM
|
||||
#define PE15 62 // X_DIR
|
||||
|
||||
// Y_MOTOR
|
||||
#define PE10 63 // Y_RESET
|
||||
#define PB10 64 // Y_PWM
|
||||
#define PE9 65 // Y_DIR
|
||||
|
||||
// Z_MOTOR
|
||||
#define PC15 66 // Z_RESET
|
||||
#define PC6 67 // Z_PWM
|
||||
#define PC0 68 // Z_DIR
|
||||
|
||||
// E1_MOTOR
|
||||
#define PC14 69 // E1_RESET
|
||||
#define PC13 70 // E1_DIR
|
||||
#define PD12 71 // E1_PWM
|
||||
|
||||
// E2_MOTOR
|
||||
#define PE4 72 // E2_RESET
|
||||
#define PE5 73 // E2_PWM
|
||||
#define PE6 74 // E2_DIR
|
||||
|
||||
// E3_MOTOR
|
||||
#define PE3 75 // E3_RESET
|
||||
#define PE2 76 // E3_DIR
|
||||
#define PB8 77 // E3_PWM
|
||||
|
||||
// This must be a literal
|
||||
#define NUM_DIGITAL_PINS 78
|
||||
// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
|
||||
#define NUM_ANALOG_INPUTS 6
|
||||
#define NUM_ANALOG_FIRST 51
|
||||
|
||||
// On-board LED pin number
|
||||
#define LED_BUILTIN PE1
|
||||
#define LED_GREEN LED_BUILTIN
|
||||
|
||||
// On-board user button
|
||||
#define USER_BTN PE7
|
||||
|
||||
// UART Definitions
|
||||
#define SERIAL_UART_INSTANCE 1 // Connected to ST-Link
|
||||
//#define SERIAL_UART_INSTANCE 2 // Connected to WIFI
|
||||
|
||||
// Default pin used for 'Serial' instance (ex: ST-Link)
|
||||
// Mandatory for Firmata
|
||||
#if SERIAL_UART_INSTANCE == 1 // ST-Link & J23
|
||||
#define PIN_SERIAL_RX PA10
|
||||
#define PIN_SERIAL_TX PA9
|
||||
#elif SERIAL_UART_INSTANCE == 2 // WIFI interface
|
||||
#define PIN_SERIAL2_RX PD6
|
||||
#define PIN_SERIAL2_TX PD5
|
||||
#else
|
||||
#error "Invalid setting for SERIAL_UART_INSTANCE."
|
||||
#endif
|
||||
|
||||
// Timer Definitions
|
||||
#define TIMER_SERVO TIM4 // TIMER_SERVO must be defined in this file
|
||||
#define TIMER_TONE TIM5 // TIMER_TONE must be defined in this file
|
||||
|
||||
/* SD detect signal */
|
||||
/*
|
||||
* By default, R67 is not provided, so SD card detect is not used.
|
||||
* Note: SD CD (pin 16 of expansion connector J23) can be connected
|
||||
* to GND in order to be able to use SD_DETECT_PIN
|
||||
*/
|
||||
/*#define SD_DETECT_PIN PA15*/
|
||||
|
||||
/* HAL configuration */
|
||||
#define HSE_VALUE 25000000U
|
||||
|
||||
/* Extra HAL modules */
|
||||
#define HAL_SD_MODULE_ENABLED
|
||||
|
||||
#endif
|
||||
|
||||
#ifdef __cplusplus
|
||||
} // extern "C"
|
||||
#endif
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#ifdef __cplusplus
|
||||
// These serial port names are intended to allow libraries and architecture-neutral
|
||||
// sketches to automatically default to the correct port name for a particular type
|
||||
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
|
||||
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
|
||||
//
|
||||
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
|
||||
//
|
||||
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
|
||||
//
|
||||
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
|
||||
//
|
||||
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
|
||||
//
|
||||
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
|
||||
// pins are NOT connected to anything by default.
|
||||
#define SERIAL_PORT_MONITOR Serial
|
||||
#define SERIAL_PORT_HARDWARE Serial1
|
||||
#endif
|
||||
|
||||
#endif // _VARIANT_ARDUINO_STM32_
|
||||
|
||||
// PA0 54 // E1_THERMISTOR
|
||||
// PA1 55 // E2_THERMISTOR
|
||||
// PA2 56 // E3_THERMISTOR
|
||||
// PA3 53 // BED_THERMISTOR_3
|
||||
// PA4 16 // SPI_CS
|
||||
// PA5 17 // SPI_SCK
|
||||
// PA6 18 // SPI_MISO
|
||||
// PA7 19 // SPI_MOSI
|
||||
// PA8 43 // V_STOP
|
||||
// PA9 0 //TX
|
||||
// PA10 1 //RX
|
||||
// PA11 30 //OTG_DM
|
||||
// PA12 31 //OTG_DP
|
||||
// PA13 20 // JTAG_TMS/SWDIO
|
||||
// PA14 21 // JTAG_TCK/SWCLK
|
||||
// PA15 25 // SD_CARD_DETECT
|
||||
// PB0 49 // E2_HEAT_PWM
|
||||
// PB1 50 // E3_HEAT_PWM
|
||||
// PB3 22 // JTAG_TDO/SWO
|
||||
// PB4 37 // USER4
|
||||
// PB5 6 // WIFI_WAKEUP
|
||||
// PB6 15 // SCL
|
||||
// PB7 14 // SDA
|
||||
// PB8 77 // E3_PWM
|
||||
// PB9 35 // USER1
|
||||
// PB10 64 // Y_PWM
|
||||
// PB12 10 // SPI_CS
|
||||
// PB13 13 // SPI_SCK
|
||||
// PB14 12 // SPI_MISO
|
||||
// PB15 11 // SPI_MOSI
|
||||
// PC0 68 // Z_DIR
|
||||
// PC1 33 //IR_ON
|
||||
// PC2 51 // BED_THERMISTOR_1
|
||||
// PC3 52 // BED_THERMISTOR_2
|
||||
// PC4 57 // E1_FAN
|
||||
// PC5 58 // E2_FAN
|
||||
// PC6 67 // Z_PWM
|
||||
// PC7 48 // E1_HEAT_PWM
|
||||
// PC8 23 // SDIO_D0
|
||||
// PC9 24 // SDIO_D1
|
||||
// PC10 26 // SDIO_D2
|
||||
// PC11 27 // SDIO_D3
|
||||
// PC12 28 // SDIO_CK
|
||||
// PC13 70 // E1_DIR
|
||||
// PC14 69 // E1_RESET
|
||||
// PC15 66 // Z_RESET
|
||||
// PD0 44 // W_STOP
|
||||
// PD1 32 //IR_OUT
|
||||
// PD2 29 // SDIO_CMD
|
||||
// PD3 2 // CTS
|
||||
// PD4 3 // RTS
|
||||
// PD5 4 // TX
|
||||
// PD6 5 // RX
|
||||
// PD7 34 // USER3
|
||||
// PD8 39 // X_STOP
|
||||
// PD9 40 // Y_STOP
|
||||
// PD10 41 // Z_STOP
|
||||
// PD11 42 // U_STOP
|
||||
// PD12 71 // E1_PWM
|
||||
// PD13 45 // BED_HEAT_2
|
||||
// PD14 46 // BED_HEAT_1
|
||||
// PD15 47 // BED_HEAT_3
|
||||
// PE0 36 // USER2
|
||||
// PE1 9 // STATUS_LED
|
||||
// PE2 76 // E3_DIR
|
||||
// PE3 75 // E3_RESET
|
||||
// PE4 72 // E2_RESET
|
||||
// PE5 73 // E2_PWM
|
||||
// PE6 74 // E2_DIR
|
||||
// PE7 38 // USER_BUTTON
|
||||
// PE8 59 // E3_FAN
|
||||
// PE9 65 // Y_DIR
|
||||
// PE10 63 // Y_RESET
|
||||
// PE11 7 // WIFI_RESET
|
||||
// PE12 8 // WIFI_BOOT
|
||||
// PE13 60 // X_RESET
|
||||
// PE14 61 // X_PWM
|
||||
// PE15 62 // X_DIR
|
||||
Loading…
Add table
Add a link
Reference in a new issue